D-NexT Primer Surfacer Mix Ratio & HardenerDai Nippon Toryo Surfacer
D-NexT Primer Surfacer is a Dai Nippon Toryo (Dai Nippon Toryo) automotive refinish surfacer. With hardener Auto Urethane Hardener #20, the mix ratio is Base 100 : Hardener 20 : Thinner 20 (by weight).
Mix ratio (by weight)
100 : 20 : 20- Base
- D-NexT Primer Surfacer
- Hardener
- Auto Urethane Hardener #20
- Thinner
- Auto Urethane Thinner ECO
- Pot life
- 20°C 60min
Weight chart
| Base | Hardener | Thinner | Total |
|---|---|---|---|
| 50 g | 10 g | 10 g | 70 g |
| 100 g | 20 g | 20 g | 140 g |
| 200 g | 40 g | 40 g | 280 g |
| 300 g | 60 g | 60 g | 420 g |
| 500 g | 100 g | 100 g | 700 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 120 g → add thinner to reach 140 g
🧮 Calculate any amount with this mixTips for using D-NexT Primer Surfacer
How to read the ratio and weigh it
The mix for D-NexT Primer Surfacer is "Base 100 : Hardener 20 : Thinner 20 (by weight)". The numbers on this page are weight ratios in grams. For example, if you weigh 300 g of base, the hardener is 60 g. Put the cup on the scale and zero it, add the base, then add the hardener while watching the scale. For the second and later components, do not zero the cup again; read the scale as a running total (see the "scale reading" line above).
Choosing a hardener
The hardener for D-NexT Primer Surfacer is Auto Urethane Hardener #20. Some systems let you choose fast, standard or slow hardeners by temperature, so check the manufacturer's temperature recommendations in the data sheet.
Pot life and how much to mix
The pot life after mixing is about 20°C 60min. It gets shorter as it gets warmer, so mix only what you can use within that time. Once the hardener is in, curing keeps going, so do not reuse leftover paint; dispose of it promptly.
Tips for surfacers
The surfacer evens out the base and supports the finish on top. Let it dry fully before sanding, and pick a grit that leaves no scratches that will show later.
Avoiding weighing mistakes
The smaller the batch, the more a small error matters. For 50 g of base, the hardener is 10 g. Misreading the hardener by 1 g shifts the hardener amount by about 10%. Use a scale that reads 0.1 g, and if you add too much, do not top up the others by eye; recalculate the whole batch or start again.
Surfacers from other brands
FAQ
What is the mix ratio of D-NexT Primer Surfacer?
with Auto Urethane Hardener #20: Base 100 : Hardener 20 : Thinner 20 (by weight).
Which hardener and thinner does D-NexT Primer Surfacer use?
hardener Auto Urethane Hardener #20, thinner Auto Urethane Thinner ECO.
How much hardener and thinner do I need for 100 g of D-NexT Primer Surfacer?
Auto Urethane Hardener #20: 20 g hardener, 20 g thinner (140 g in total).
More Dai Nippon Toryo Surfacers
Mix ratios are converted from the manufacturer's technical data sheet (TDS) into weight ratios you can measure on a scale. Products are reformulated from time to time, so always check the latest TDS before you mix. Product information: Dai Nippon Toryo official site