Urethane Primer Surfacer SB Alpha Mix Ratio & HardenerNippon Paint Surfacer
Urethane Primer Surfacer SB Alpha is a Nippon Paint (Nippon Paint) automotive refinish surfacer. With hardener SB Alpha Hardener (10:1), the mix ratio is Base 100 : Hardener 10 : Thinner 25 (by weight).
Mix ratio (by weight)
100 : 10 : 25- Base
- Urethane Primer Surfacer SB Alpha
- Hardener
- SB Alpha Hardener (10:1)
- Thinner
- Mighty Lac G-II Thinners (various)
- Pot life
- 20°C 2h
Weight chart
| Base | Hardener | Thinner | Total |
|---|---|---|---|
| 50 g | 5 g | 12.5 g | 67.5 g |
| 100 g | 10 g | 25 g | 135 g |
| 200 g | 20 g | 50 g | 270 g |
| 300 g | 30 g | 75 g | 405 g |
| 500 g | 50 g | 125 g | 675 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 110 g → add thinner to reach 135 g
🧮 Calculate any amount with this mixTips for using Urethane Primer Surfacer SB Alpha
How to read the ratio and weigh it
The mix for Urethane Primer Surfacer SB Alpha is "Base 100 : Hardener 10 : Thinner 25 (by weight)". The numbers on this page are weight ratios in grams. For example, if you weigh 300 g of base, the hardener is 30 g. Put the cup on the scale and zero it, add the base, then add the hardener while watching the scale. For the second and later components, do not zero the cup again; read the scale as a running total (see the "scale reading" line above).
Choosing a hardener
The hardener for Urethane Primer Surfacer SB Alpha is SB Alpha Hardener (10:1). Some systems let you choose fast, standard or slow hardeners by temperature, so check the manufacturer's temperature recommendations in the data sheet.
Pot life and how much to mix
The pot life after mixing is about 20°C 2h. It gets shorter as it gets warmer, so mix only what you can use within that time. Once the hardener is in, curing keeps going, so do not reuse leftover paint; dispose of it promptly.
Tips for surfacers
The surfacer evens out the base and supports the finish on top. Let it dry fully before sanding, and pick a grit that leaves no scratches that will show later.
Avoiding weighing mistakes
The smaller the batch, the more a small error matters. For 50 g of base, the hardener is 5 g. Misreading the hardener by 1 g shifts the hardener amount by about 20%. Use a scale that reads 0.1 g, and if you add too much, do not top up the others by eye; recalculate the whole batch or start again.
Surfacers from other brands
FAQ
What is the mix ratio of Urethane Primer Surfacer SB Alpha?
with SB Alpha Hardener (10:1): Base 100 : Hardener 10 : Thinner 25 (by weight).
Which hardener and thinner does Urethane Primer Surfacer SB Alpha use?
hardener SB Alpha Hardener (10:1), thinner Mighty Lac G-II Thinners (various).
How much hardener and thinner do I need for 100 g of Urethane Primer Surfacer SB Alpha?
SB Alpha Hardener (10:1): 10 g hardener, 25 g thinner (135 g in total).
More Nippon Paint Surfacers
Mix ratios are converted from the manufacturer's technical data sheet (TDS) into weight ratios you can measure on a scale. Products are reformulated from time to time, so always check the latest TDS before you mix. Product information: Nippon Paint official site