D834 DP40 Epoxy Surfacer Mix Ratio & HardenerPPG Surfacer
D834 DP40 Epoxy Surfacer is a PPG (PPG) automotive refinish surfacer. You can choose from 2 hardeners. With hardener DP402 Hardener (D835), the mix ratio is Base 100 : Hardener 61 (by weight).
With hardener DP402 Hardener (D835)
100 : 61- Base
- D834 DP40 Epoxy Surfacer
- Hardener
- DP402 Hardener (D835)
- Thinner
- None
- Pot life
- 20°C 16h
Weight chart
| Base | Hardener | Total |
|---|---|---|
| 50 g | 30.5 g | 80.5 g |
| 100 g | 61 g | 161 g |
| 200 g | 122 g | 322 g |
| 300 g | 183 g | 483 g |
| 500 g | 305 g | 805 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 161 g
🧮 Calculate any amount with this mixWith hardener DP402 Hardener (D835)
100 : 61 : 32- Base
- D834 DP40 Epoxy Surfacer
- Hardener
- DP402 Hardener (D835)
- Thinner
- GRS Thinner (D808)
- Pot life
- 20°C 16h
Weight chart
| Base | Hardener | Thinner | Total |
|---|---|---|---|
| 50 g | 30.5 g | 16 g | 96.5 g |
| 100 g | 61 g | 32 g | 193 g |
| 200 g | 122 g | 64 g | 386 g |
| 300 g | 183 g | 96 g | 579 g |
| 500 g | 305 g | 160 g | 965 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 161 g → add thinner to reach 193 g
🧮 Calculate any amount with this mixTips for using D834 DP40 Epoxy Surfacer
How to read the ratio and weigh it
The mix for D834 DP40 Epoxy Surfacer is "Base 100 : Hardener 61 (by weight)". The numbers on this page are weight ratios in grams. For example, if you weigh 300 g of base, the hardener is 183 g. Put the cup on the scale and zero it, add the base, then add the hardener while watching the scale. For the second and later components, do not zero the cup again; read the scale as a running total (see the "scale reading" line above).
Choosing a hardener
The hardener for D834 DP40 Epoxy Surfacer is DP402 Hardener (D835). Some systems let you choose fast, standard or slow hardeners by temperature, so check the manufacturer's temperature recommendations in the data sheet.
Pot life and how much to mix
The pot life after mixing is about 20°C 16h. It gets shorter as it gets warmer, so mix only what you can use within that time. Once the hardener is in, curing keeps going, so do not reuse leftover paint; dispose of it promptly.
Tips for surfacers
The surfacer evens out the base and supports the finish on top. Let it dry fully before sanding, and pick a grit that leaves no scratches that will show later.
Avoiding weighing mistakes
The smaller the batch, the more a small error matters. For 50 g of base, the hardener is 30.5 g. Misreading the hardener by 1 g shifts the hardener amount by about 3.3%. Use a scale that reads 0.1 g, and if you add too much, do not top up the others by eye; recalculate the whole batch or start again.
Surfacers from other brands
FAQ
What is the mix ratio of D834 DP40 Epoxy Surfacer?
with DP402 Hardener (D835): Base 100 : Hardener 61 (by weight). with DP402 Hardener (D835): Base 100 : Hardener 61 : Thinner 32 (by weight).
Which hardener and thinner does D834 DP40 Epoxy Surfacer use?
hardener DP402 Hardener (D835), no thinner. hardener DP402 Hardener (D835), thinner GRS Thinner (D808).
How much hardener and thinner do I need for 100 g of D834 DP40 Epoxy Surfacer?
DP402 Hardener (D835): 61 g hardener (161 g in total). DP402 Hardener (D835): 61 g hardener, 32 g thinner (193 g in total).
More PPG Surfacers
Mix ratios are converted from the manufacturer's technical data sheet (TDS) into weight ratios you can measure on a scale. Products are reformulated from time to time, so always check the latest TDS before you mix. Product information: PPG Refinish official site