NS2602 / NS2607 Plastic Primer Surfacer Mix Ratio & HardenerCromax Surfacer
NS2602 / NS2607 Plastic Primer Surfacer is a Cromax (Axalta) automotive refinish surfacer. You can choose from 3 hardeners. With hardener XK203 (Spot & Panel Repair), the mix ratio is Base 100 : Hardener 14 : Additive 26 (by weight).
With hardener XK203 (Spot & Panel Repair)
100 : 14 : 26- Base
- NS2602 / NS2607 Plastic Primer Surfacer
- Hardener
- XK203 (Spot & Panel Repair)
- Additive
- AZ9600
- Pot life
- 20°C 1h
Weight chart
| Base | Hardener | Additive | Total |
|---|---|---|---|
| 50 g | 7 g | 13 g | 70 g |
| 100 g | 14 g | 26 g | 140 g |
| 200 g | 28 g | 52 g | 280 g |
| 300 g | 42 g | 78 g | 420 g |
| 500 g | 70 g | 130 g | 700 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 114 g → add additive to reach 140 g
🧮 Calculate any amount with this mixWith hardener XK205 (Standard)
100 : 14 : 26- Base
- NS2602 / NS2607 Plastic Primer Surfacer
- Hardener
- XK205 (Standard)
- Additive
- AZ9600
- Pot life
- 20°C 1h
Weight chart
| Base | Hardener | Additive | Total |
|---|---|---|---|
| 50 g | 7 g | 13 g | 70 g |
| 100 g | 14 g | 26 g | 140 g |
| 200 g | 28 g | 52 g | 280 g |
| 300 g | 42 g | 78 g | 420 g |
| 500 g | 70 g | 130 g | 700 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 114 g → add additive to reach 140 g
🧮 Calculate any amount with this mixWith hardener XK206 (Large Area)
100 : 14 : 26- Base
- NS2602 / NS2607 Plastic Primer Surfacer
- Hardener
- XK206 (Large Area)
- Additive
- AZ9600
- Pot life
- 20°C 1h
Weight chart
| Base | Hardener | Additive | Total |
|---|---|---|---|
| 50 g | 7 g | 13 g | 70 g |
| 100 g | 14 g | 26 g | 140 g |
| 200 g | 28 g | 52 g | 280 g |
| 300 g | 42 g | 78 g | 420 g |
| 500 g | 70 g | 130 g | 700 g |
Scale readings (for 100 g of base): base 100 g → add hardener to reach 114 g → add additive to reach 140 g
🧮 Calculate any amount with this mixTips for using NS2602 / NS2607 Plastic Primer Surfacer
How to read the ratio and weigh it
The mix for NS2602 / NS2607 Plastic Primer Surfacer is "Base 100 : Hardener 14 : Additive 26 (by weight)". The numbers on this page are weight ratios in grams. For example, if you weigh 300 g of base, the hardener is 42 g. Put the cup on the scale and zero it, add the base, then add the hardener while watching the scale. For the second and later components, do not zero the cup again; read the scale as a running total (see the "scale reading" line above).
Choosing a hardener
NS2602 / NS2607 Plastic Primer Surfacer works with 3 hardeners (XK203 (Spot & Panel Repair), XK205 (Standard), XK206 (Large Area)). You choose by temperature and working time, but follow the manufacturer's temperature recommendations in the technical data sheet. Changing the hardener can change the mix ratio, so always check the table above.
Pot life and how much to mix
The pot life after mixing is about 20°C 1h. It gets shorter as it gets warmer, so mix only what you can use within that time. Once the hardener is in, curing keeps going, so do not reuse leftover paint; dispose of it promptly.
Tips for surfacers
The surfacer evens out the base and supports the finish on top. Let it dry fully before sanding, and pick a grit that leaves no scratches that will show later.
Avoiding weighing mistakes
The smaller the batch, the more a small error matters. For 50 g of base, the hardener is 7 g. Misreading the hardener by 1 g shifts the hardener amount by about 14.3%. Use a scale that reads 0.1 g, and if you add too much, do not top up the others by eye; recalculate the whole batch or start again.
Surfacers from other brands
FAQ
What is the mix ratio of NS2602 / NS2607 Plastic Primer Surfacer?
with XK203 (Spot & Panel Repair): Base 100 : Hardener 14 : Additive 26 (by weight). with XK205 (Standard): Base 100 : Hardener 14 : Additive 26 (by weight). with XK206 (Large Area): Base 100 : Hardener 14 : Additive 26 (by weight).
Which hardener and thinner does NS2602 / NS2607 Plastic Primer Surfacer use?
hardener XK203 (Spot & Panel Repair), additive AZ9600. hardener XK205 (Standard), additive AZ9600. hardener XK206 (Large Area), additive AZ9600.
How much hardener and thinner do I need for 100 g of NS2602 / NS2607 Plastic Primer Surfacer?
XK203 (Spot & Panel Repair): 14 g hardener, 26 g additive (140 g in total). XK205 (Standard): 14 g hardener, 26 g additive (140 g in total). XK206 (Large Area): 14 g hardener, 26 g additive (140 g in total).
More Cromax Surfacers
Mix ratios are converted from the manufacturer's technical data sheet (TDS) into weight ratios you can measure on a scale. Products are reformulated from time to time, so always check the latest TDS before you mix. Product information: Cromax official site